Start with the scene the pieces are built to tell
Encounter 02: Prison Passage is the second encounter of Caverns Deep, and its premise is simple: a wide tunnel ends at crude wooden bars, and somewhere beyond them a cry for help. That story should drive your build and paint choices more than any generic dungeon palette. You are not decorating a corridor; you are setting up a rescue.
The complete encounter includes 26 pieces: a variety of Cavern Passage pieces, a Magnetic Wall with Chained Conduit Crystal, a Cave Door with Portcullis Insert, a Hidden Nook Wall, Mercer the Prisoner, a Mushroom Cluster, and a Cavern Double Door with a Crude Wooden Gate. The set can be used as a stand-alone adventure or as part of a prewritten module available free from the manufacturer.
Catalog facts that shape your build and paint plan
- Encounter 02 - Prison Passage (Unpainted): Prison Passage is the 2nd encounter of Caverns Deep and includes 26 pieces. Knowing the piece count and encounter role helps you plan a layout that uses the whole set rather than treating it as scatter.

Encounter 02 - Prison Passage (Unpainted) - Encounter 02 - Prison Passage (Unpainted): The set includes a variety of Cavern Passage pieces, a Magnetic Wall with Chained Conduit Crystal, a Cave Door with Portcullis Insert, a Hidden Nook Wall, Mercer the Prisoner, a Mushroom Cluster, and a Cavern Double Door with a Crude Wooden Gate. These named pieces are your focal points. Decide early which ones get the most paint attention and where they sit in the corridor.
- Encounter 02 - Prison Passage (Unpainted): Crude wooden bars block the end of the wide tunnel ahead, and a cry for help comes from the darkness. The barred gate is the visual punchline of the encounter. Your paint scheme should make it readable from across the table.
- Encounter 02 - Prison Passage (Unpainted): Encounter 02: Prison Passage can be used as a stand-alone adventure or as part of a prewritten module available free. If you plan to run the module, build the corridor to match its map; if not, you can arrange the pieces for your own rescue scenario.
Plan the corridor before you glue or paint anything
A dungeon passage terrain build works best when the layout supports play. Lay out the pieces dry before any paint touches them.
- Lay out the passage pieces first: Use the Cavern Passage pieces to form the wide tunnel that leads to the barred gate. Leave enough room at the table edge for miniatures to enter and for you to reach the gate.
- Place the double door and gate as the focal wall: The Cavern Double Door with a Crude Wooden Gate is the end point of the tunnel. Put it where players can see it clearly and where the gate can be opened or described without moving half the build.
- Work in the Cave Door with Portcullis Insert and Hidden Nook Wall: These pieces add decision points. The portcullis door can be a secondary barrier; the hidden nook wall can conceal a clue or an escape route. Decide their roles before you paint so their details read clearly.
- Set Mercer the Prisoner and the Mushroom Cluster: Mercer is the reason for the rescue. Place the miniature behind the bars or near the hidden nook. The mushroom cluster adds cavern flavor; put it where it does not hide important line-of-sight details.
- Check the Magnetic Wall with Chained Conduit Crystal: This wall piece is a strong visual element. Decide whether it is a side wall, a focal point near the gate, or part of the hidden nook area. Its magnetic feature may help with placement, but the supplied information does not describe how it attaches to other pieces, so test it physically before finalizing.
Prep unpainted Dwarvenite for paint that stays put
The set is unpainted Dwarvenite. The supplied catalog information does not include specific preparation or care instructions, so the following is general hobby practice rather than a manufacturer procedure. Start by washing the pieces in warm, mild soapy water to remove any mold release or dust, then rinse and let them dry completely. Dwarvenite is a flexible material, so avoid harsh solvents and test any primer or paint on an inconspicuous area first.
Do not sand or scrape details aggressively; the sculpted texture is what makes the cavern walls and gate read at the table. If you plan to prime, use a primer labeled for flexible plastics and apply thin coats. The catalog does not confirm which paints or primers are recommended, so treat this as your own test-and-check step.
Paint the prison corridor in a sensible order
Paint from the largest areas to the smallest details so you do not have to reach back into finished sections.
- Base coat the cavern passage pieces: Choose a rock tone that contrasts with the wooden gate and the prisoner. Keep the base coat thin and let it dry fully before judging coverage.
- Paint the wooden gate and bars: The crude wooden bars are the story's focal point. Use a distinct wood color and a darker wash in the gaps to make the bars read as separate from the stone. The catalog describes the gate as crude wood, so avoid a clean, finished furniture look.
- Detail the Cave Door with Portcullis Insert: Paint the portcullis to look like a secondary barrier: darker metal or wood that contrasts with the surrounding stone. Keep the insert visually separate so players understand it can be opened or blocked.
- Paint the Magnetic Wall with Chained Conduit Crystal: The crystal is a natural color accent. Pick a hue that stands out against the rock and wood, and paint the chains a dark metal tone. The catalog does not specify a crystal color, so this is your choice.
- Finish Mercer the Prisoner and the Mushroom Cluster: Mercer should be visible against the corridor background. Paint the mushroom cluster in a contrasting color so it reads as a distinct cavern detail. Keep both simple; they are small elements that support the scene rather than dominate it.
Checkpoints while the paint dries
These are practical checks you can make between coats, not manufacturer instructions.
- Check readability from table distance: Stand a few feet back. Can you tell where the gate is, where the prisoner is, and which door is the portcullis? If not, increase contrast on those focal points.
- Check that the gate still opens or reads as a barrier: If paint builds up in moving parts or around the gate, clean the contact areas before the paint fully cures. The supplied information does not describe the gate's mechanism, so test gently.
- Check color harmony across the set: The cavern pieces, wooden gate, and crystal should look like they belong in the same underground space. A shared wash or a limited palette helps unify them.
- Check the hidden nook still hides: If you paint the Hidden Nook Wall, make sure the concealment feature is not highlighted so brightly that it gives away the secret. Keep its surface similar to the surrounding walls.
Set up the encounter for play
Once painted, rebuild the corridor in the layout you planned. Put the wide tunnel first, then the gate wall, with the portcullis door and hidden nook as side options. Place Mercer behind the bars and the mushroom cluster where it adds atmosphere without blocking movement. If you are running the free prewritten module, match the layout to its map; otherwise, use the pieces to create a clear rescue route.
The catalog does not provide dimensions or a recommended layout, so let your table space and the module text guide you. Keep the path to the gate wide enough for miniatures and leave room for players to move around the build.


